hello! I am trying to port my usb dance pad to Atmega88
http://www.avrfreaks.net/index.php?modu ... em_id=1675
Fixed timer names in the code and just replaces atmega8 with atemega88 on the pcb expecting it to work.
I am using atmega88-20 at 16Mhz
The weird thin is that AVR USB does not work. Windows says "device is not recognized". I have found some messages about it on google and here but never found a single solution.
Does AVR USB work with atmega88 at all?
I have disabled UART and external T0 line at the beginning of my code to avoid any interference. It did not help.
I replaces atmega88 with atmega8 and programmed with the atmega8 code version - everything works. So, it is not the schematic, it is something related to atmega88 features.
AVR USB on Atmega88
Link above is broken.
- make sure the fuses are correct, they are different for m8 and m88
- make sure you recompile the project w/ MCU=atmega88
- are you using 3V3 Z-diodes on D+/D- ? If so, replace them w/ 500mW 3V6 diodes.
- if you run the m88 at 3.3V, change it to 5V @ 16MHz. Use Z-diodes.
- Atmel has a m8 to m88 migration guide online here.
- make sure the fuses are correct, they are different for m8 and m88
- make sure you recompile the project w/ MCU=atmega88
- are you using 3V3 Z-diodes on D+/D- ? If so, replace them w/ 500mW 3V6 diodes.
- if you run the m88 at 3.3V, change it to 5V @ 16MHz. Use Z-diodes.
- Atmel has a m8 to m88 migration guide online here.
Link above is broken.
try this one:
http://www.artemlive.com/cgi-bin/news?c=v&id=749
- make sure the fuses are correct, they are different for m8 and m88
Fuses are correct. I've read the datasheet. The mcu is at 16Mhz and i checked it.
- make sure you recompile the project w/ MCU=atmega88
yes, i did
- are you using 3V3 Z-diodes on D+/D- ? If so, replace them w/ 500mW 3V6 diodes.
i use 3.6V
- if you run the m88 at 3.3V, change it to 5V @ 16MHz. Use Z-diodes.
i run mcu at 5V and use zener dioides 3.6v
- Atmel has a m8 to m88 migration guide online here.
thanks, i'll take a look, but my part of software works fine. Only AVR USB does not work. I have already ported my times routines and some other stuff to atmega88 just reading the datasheet for 88. I've checked - my part works fine.
Did you personally run AVR USB on atmega88?
Almost 
I was redesigning my mega8 based project and actually got a mega88. Ended up using a tiny461 instead, since it has exactly the right size for what I need. I did look at the 88 specs in detail tho and I also ran into similar problems w/ the 461 (the 461 uses a newer chip design, similar to the 88 ) -- 3V3 diodes would work on the 8 but not on the 461, had to use 3V6 diodes. Also the pull-up on D- is a lot more sensitive to value variations on the 461. I nailed it down to changes in the I/O pin thresholds and hysteresis, you can find those values in the data sheets under "Typical Characteristics". Assuming 4.5V at 25C the values for the chips are approx.:
This nicely explains why 3V3 ZDs would work w/ the m8 but not the t461. You may have a similar problem, try leaving the diodes out (works on some hosts) or changing them to 3V7 or 3V8 ZDs.
Code: Select all
high low
m8: 1.70V 1.25V
m88: 2.25V 2.15V
t461: 2.30V 1.95VThis nicely explains why 3V3 ZDs would work w/ the m8 but not the t461. You may have a similar problem, try leaving the diodes out (works on some hosts) or changing them to 3V7 or 3V8 ZDs.